News:

New registrations to the forum only by request to admin@underservice.org

Main Menu

Romero Experiments

Started by Romero, June 27, 2011, 11:14:38 PM

Previous topic - Next topic

free_nrg

Quote from: Romero on April 30, 2014, 03:56:09 PM
Quote from: free_nrg on April 30, 2014, 03:42:30 PM
Thanks for the info Romero.
Do you have any recommendations for a dc/dc converter?

Just powering one coil with hall circuit, @820 rpm, getting 22v in a 10000 if cap. Running off a 11.2v Lipo needing a charge. No bemf collection yet or coil shorting. Gonna build the self triggered circuit today if I can dig up all the parts.

Thanks!
Now I am using this one http://www.ebay.co.uk/itm/10A-DC-DC-600W-10-60V-to-12-80V-Boost-Converter-Step-up-Module-Power-Supply-UK-/350975904870?pt=UK_BOI_Electrical_Test_Measurement_Equipment_ET&hash=item51b7cb4c66
I have also used this one for low power experiments http://www.ebay.co.uk/itm/New-10Pcs-DC-DC-LM2596-Converter-Buck-Adjustable-Step-Down-Power-Module-1-5-35V-/370844697207?pt=UK_BOI_Electrical_Test_Measurement_Equipment_ET&hash=item5658110277


Thanks for the links!

Romero

Quote from: free_nrg on April 30, 2014, 04:34:14 PM
Quote from: crazycut06 on April 30, 2014, 03:59:59 PM
Nice build there free_nrg, does your coil speed up under load while charging your lipo batt?
What gauge is the wire you used? Any videos? Thanks!

Regards
Cc

No speed under load yet. Coil is 20 awg. @442 turns 2.4 ohms. No videos yet. I need to build a better drive circuit. And bemf recovery. Just got it running last night.
For 2.4 ohm coil you will need very high RPM but you can use 2 coils in series to get speed up effect.
Another simple and cheap dc to dc convertor is any laptop charger or power supply for a desktop computer.
Most of them can work fine with input from 90 volts to 240 volts while maintaining the output voltage. Most of them are 18-19 volts  output but you can modify the output power or use it as is. You can apply ac or dc but if used to utilise BEMF from the driver coil then must change the input bridge diodes with fast ones.

Success,
Romero

crazycut06

Quote from: free_nrg on April 30, 2014, 04:34:14 PM
Quote from: crazycut06 on April 30, 2014, 03:59:59 PM
Nice build there free_nrg, does your coil speed up under load while charging your lipo batt?
What gauge is the wire you used? Any videos? Thanks!

Regards
Cc

No speed under load yet. Coil is 20 awg. @442 turns 2.4 ohms. No videos yet. I need to build a better drive circuit. And bemf recovery. Just got it running last night.

Thanks, pls. Feel free to share your progress, my setup is slowing down with 12v 10w bulb load, but if i short it out, rpm almost doesn't drop, my coils are thick gauge wires, i get 9v with lots of amps, need to wind a smaller gauge to get sul...more to do.....keep it up....

Regards
Cc

Romero

Some of the parts for my new motor/generator arrived today. One coil ready, lots to go...
I am calling this one SRG4.

Romero

The new generator partially assembled, ready for a quick test.

Romero

#530
Today I received another grid tie inverter. The previous one (Powerjack 1200) died after about one year of use.
Now I got a serious one EverSolar TL3200. Installed and tested just before being too dark outside and still got some power.

Romero

#531
I have just received few flexible solar panels. Each one is putting out 92Watts/ 319volts. This is ideal for all professional grid tie inverters working with input voltages from 125-500volts.

Romero

Flexible solar panels installed on top of my shed.

Romero

Recent experiments...

Romero

Recent experiments...

nicolaienvlad

Quote from: Romero on June 07, 2014, 09:55:19 PM
Recent experiments...

Foarte interesante noutatile de la ROMERO !
Va rog ,daca puteti , precizati numarul de miezuri toroidale din schema cu oscilatorul cu BD139 si BD140 , alimentat de la 1.5 V...
Merci in avans.
nicolaienvlad

Romero

Quote from: nicolaienvlad on June 18, 2014, 04:27:09 PM
Quote from: Romero on June 07, 2014, 09:55:19 PM
Recent experiments...

Foarte interesante noutatile de la ROMERO !
Va rog ,daca puteti , precizati numarul de miezuri toroidale din schema cu oscilatorul cu BD139 si BD140 , alimentat de la 1.5 V...
Merci in avans.
nicolaienvlad
te rog sa imi dai link la schema despre care vorbesti, nu stiu exact la ce anume te referi

Romero

nicolaienvlad

Multumesc pentru mesaj !
Schema la care ma refer este in atasamentul self runing.jpg(59,9KB..)
din raspunsul dvs
Reply #12 on Nov,2013
@Dave45

Romero

Quote from: nicolaienvlad on June 20, 2014, 09:31:49 AM
Multumesc pentru mesaj !
Schema la care ma refer este in atasamentul self runing.jpg(59,9KB..)
din raspunsul dvs
Reply #12 on Nov,2013
@Dave45
chiar ma zapacesti... nu am idee la care schema te referi, am testat o multime. Mergi la pagina la care te referi dai Copy la link apoi dai Paste aici. ? Te referi la miezuri toroidale... la mai multe? sau nu mai inteleg eu bine de atata stat prin strainatati :)

Romero

Romero

nicolaienvlad

Ref. la miezuri toroidale din schema oscilatorului cu BD139 si BD140 data de dvs.
nu reusesc sa fac copy link samd[probabil nu-i dotat softul meu , ca sa nu zic altceva..]
INTREBARE : 1) pot face un mic clip video pe youtu..  si sa va trimit linkul
                     2)pot trimite un email pe adresa dvs. , daca aveti una
Tank , in avans !
nicolaienvlad