Romero Experiments

[toranarod]

Hi Romero,
Do you have a schematic posted for your coil shorting experiment, in particular the circuit in the attachment:

(had to attatch the picture to this post cause my server is under extreme load..)

Thanks
Regards Hitman

Hi,
there is nothing special, just bridge rectifiers connected to all coils around the rotor.
The shorting in that experiment was done using a reed in series with a capacitor.
Mechanical shorting or switching is the best and nothing can replicate that, unfortunately the reed switch will not last too much.Mosfets are good enough but must have many of them in parallel to get close to the mechanical switch, also the lowest resistance we can get.

Best regards,
Romero

I am looking for any help I can get to find out if its possible to get acceleration greater than no coil present in the system.
If you read this Romero do you know. please help.

[toranarod]

RG

http://www.falconacoustics.co.uk/audio-inductors-ferrite-air-core-iron-dust/audio-inductors-4mh-6mh-ferrite-air-core-iron-dust.html

Is this where you got your coils,  I use audio inductors  to. like you the main problem for people like us on a budget is manufacturing.
cheers Rod

[Romero]

RG

http://www.falconacoustics.co.uk/audio-inductors-ferrite-air-core-iron-dust/audio-inductors-4mh-6mh-ferrite-air-core-iron-dust.html

Is this where you got your coils,  I use audio inductors  to. like you the main problem for people like us on a budget is manufacturing.
cheers Rod

Hi,
I have used them to get coils and irondust cores. I also had custom coils made by them. Email them and ask. Depending on what you want, custom coils can be expensive.

Regards,
Romero

[landownunder]

Hi romero please answer toranarods question if you have had this effect if at all possible. below is the question he has asked you thanks ron

I am looking for any help I can get to find out if its possible to get acceleration greater than no coil present in the system.
If you read this Romero do you know. please help.  please please ;D ;D ;D ;D ;D

[toranarod]

Hi romero please answer toranarods question if you have had this effect if at all possible. below is the question he has asked you thanks ron

I am looking for any help I can get to find out if its possible to get acceleration greater than no coil present in the system.
If you read this Romero do you know. please help.  please please ;D ;D ;D ;D ;D

Thank you Landownunder
this is a very important question because we need to know or have some idea what is enough how far can acceleration under load Go.
I needs some idea where to take the research. 
If it can increase past No coil installed then the next step will be to run a generator from only a load.
This is a concept I have never seen in a video forum or talked about.   
I am planing a much larger unit to generate usable power.   

[Romero]

Hi romero please answer toranarods question if you have had this effect if at all possible. below is the question he has asked you thanks ron

I am looking for any help I can get to find out if its possible to get acceleration greater than no coil present in the system.
If you read this Romero do you know. please help.  please please ;D ;D ;D ;D ;D

Thank you Landownunder
this is a very important question because we need to know or have some idea what is enough how far can acceleration under load Go.
I needs some idea where to take the research. 
If it can increase past No coil installed then the next step will be to run a generator from only a load.
This is a concept I have never seen in a video forum or talked about.   
I am planing a much larger unit to generate usable power.   

Hi,
I have tested with aircore and that is like no coil when no load on it and I have got acceleration. I have also got it with MuMetal core. I have not measured the difference with other type of cores but I will do some testing and I will confirm. In my case, now I don't care too much about the acceleration, I want it to stay about the same when loaded.
When the acceleration changes, depending on the load, then we can only use a fix load and that is not what I am looking for.
By the end of this month I should have the new generator ready for testing. I am still waiting for some parts to finish it and at the same time I am planing to build something else too.

Best Regards,
Romero

[landownunder]

hi romero good luck with your experiments with your generator and other item, will you share with anyone your Knowledge at the end of month or will you sell plans for it or will it be another breakthrough that will disappear like a lot of others. please think about changing the world for the better and don't listen to all the negative comments from others. i wish you and your family all the best thanks for at least getting people on the right track with there experiments. ron

can you expand a bit on how you acceleration under load for toranarod to help him out please. like what sort of coil and windings etc

[Romero]

hi romero good luck with your experiments with your generator and other item, will you share with anyone your Knowledge at the end of month or will you sell plans for it or will it be another breakthrough that will disappear like a lot of others. please think about changing the world for the better and don't listen to all the negative comments from others. i wish you and your family all the best thanks for at least getting people on the right track with there experiments. ron

can you expand a bit on how you acceleration under load for toranarod to help him out please. like what sort of coil and windings etc

I have shared a lot and I am still sharing. The current project i need to have it ready first. At the moment I am only guessing the results and hoping to be good.
Toranarod has enough info to continue, i don't have anything else to offer in helping him or anyone to get the speedup effect.
Check the forums and see that Mariuscivic had a small accident with his rotor and now after fixing it, is not getting the effect anymore but still same rotor and same coils... how can I teach someone when even people who had it working are not able to replicate all the time... practice is the answer.

Regards,
Romero

[Hitman]

@ toranarod
I'm not sure if this is what your looking for but yesterday I made a new coil and connected it to my gen with long enough wires so I can take it out of the system.
With the coil out of the system, I start up the gen, once up to speed I move the coil into the correct position and I get major acceleration.

I will try to make a video of the effect and post to youtube if you would like to see it.

@ romero
I connected up 4 coils last night and noticed that the fourth coil had much less voltage then the first coil, is this the reason you added a second drive coil ?

Cheers Hitman.

[toranarod]

@ toranarod
I'm not sure if this is what your looking for but yesterday I made a new coil and connected it to my gen with long enough wires so I can take it out of the system.
With the coil out of the system, I start up the gen, once up to speed I move the coil into the correct position and I get major acceleration.

I will try to make a video of the effect and post to youtube if you would like to see it.

@ romero
I connected up 4 coils last night and noticed that the fourth coil had much less voltage then the first coil, is this the reason you added a second drive coil ?

Cheers Hitman.

this is good news  Please keep us informed.

[Romero]

@ toranarod
I'm not sure if this is what your looking for but yesterday I made a new coil and connected it to my gen with long enough wires so I can take it out of the system.
With the coil out of the system, I start up the gen, once up to speed I move the coil into the correct position and I get major acceleration.

I will try to make a video of the effect and post to youtube if you would like to see it.

@ romero
I connected up 4 coils last night and noticed that the fourth coil had much less voltage then the first coil, is this the reason you added a second drive coil ?

Cheers Hitman.

Hi,
if all coils are identical then all should give about the same voltage.You must have something different to that coil or you have an internal short in the coil.
Do a video if you can, that can help all others.
Anyone trying to get the effect with aircore?

Romero

[Hitman]

Thank you Landownunder
this is a very important question because we need to know or have some idea what is enough how far can acceleration under load Go.
I needs some idea where to take the research. 
If it can increase past No coil installed then the next step will be to run a generator from only a load.
This is a concept I have never seen in a video forum or talked about.   
I am planing a much larger unit to generate usable power.   

@toranarod
Hehe I got your name wrong in the video, sorry bout that.
Is this the effect your looking for ?
http://youtu.be/gMvNlDbe05U

Cheers Hitman

[Romero]

@toranarod

Hi,
nice video.
I am still not 100% sure how you connected the generator coil but the effect is there. Are you saying that you are using the BEMF from the drive coil, applying it to the generator coil,... ?
What is the core used?

Romero

[Hitman]

@toranarod

Hi,
nice video.
I am still not 100% sure how you connected the generator coil but the effect is there. Are you saying that you are using the BEMF from the drive coil, applying it to the generator coil,... ?
What is the core used?

Romero

@ romero
Yes I connected the BEMF to 1 of the windings of the bi-filer gen coil and core is ferrite rods from a comp. PSU.
I was trying to directly induce the gen coil with the BEMF, maybe I should try with more coils !! :)

Cheers Htiman.

[toranarod]

@toranarod

Hi,
nice video.
I am still not 100% sure how you connected the generator coil but the effect is there. Are you saying that you are using the BEMF from the drive coil, applying it to the generator coil,... ?
What is the core used?

Romero

great work.  I have so many question I don't know where to start. based no my own work and observation I would like to see your motor.
and share some things with you and Romero that I think are happening and get your input.
its getting to a point where all of the interested party's should be put in a work shop together to create a think tank. We could sort this out once and for all.
It will take a long time by corresponding.

My concerned interest in some aspects of this is created by what i had in one setup on my bench.  I had the same effect in one of my motors.
I just could not get verification why. There where to many anomalies in the figures. As Romero has stated many times I could not replicate it in a different setup. 
the extra speed was some how linked to feed back from the generator coil to the drive coil. What the generator coil did was mirrored in the  drive coil.  this should not have been possible.
my drive coil was controlled by a processor and completely Independent  of the system speed. and any increase in speed would register in current flow. but it behaved in a revers to what it should
have.