Hitman Experiments

[Hitman]

Experiments and work in progress.

[Hitman]

300 turn uni-filer coil pair
No load:
2685 rpm - 2.640 VDC

With load:
2670 rpm - .406 VDC


I beleive I am out of resonance and also need more voltage so I went bi-filer :)

300 turn bi-filer coil pair
No load:
2685 rpm - 6.29 VDC

With load:
2620.2 rpm - 1.316 VDC

[Hitman]

For some reason I couldn't upload the entire video :(

just wanted to show the huge increase in voltage when you find the right spot.

http://youtu.be/xG9TqR0KJrk

[landownunder]

Very well done hitman keep up the good work. sooner or later someone will prove romero is a brilliant experimenter. wish you all the best with your experiments. ron

[scratchrobot]

Nice build, in the video are you dumping to a capacitor?

[Hitman]

yes I used a 250vac - 11uf, I used this value because it showed rapid changes in voltage.

[scratchrobot]

I'm using 40v DC caps but I will test some AC caps as soon as I get them.

[Hitman]

Hummmm,
I just saw something I forgot to disconnect, I left the neg of the output connected to the neg of the battery and when I disconnect it the effect goes away ?????
This is how I have it connected:

[Hitman]

I was trying to find the best rpm on my mini-muller and when I hit about 3000rpm one of my magnets came off and rocketed out leaving a magnet size hole in the lab wall !!!

I must now build a better rotor, I knew it would come apart sooner or later (it was for testing purposes anyways)

I also found a couple of videos that were very interesting.
http://youtu.be/rbkvXoDfk7g
http://youtu.be/PoEXCweMxhk

[Hitman]

After achieving the same effect as romero did, but only using only 1 coil, I wanted to add another coil but spacing, size and dimensions of all components must be all calculated in advance in order for this to work as romero's muller project did.

Unfortunately because of my rotor design and size of my coils, I can not add a 2nd coil to the setup, I must either increase the size of my rotor or decrease the size of my coils !! :(

The effect can be seen using only 1 coil and a NSNS rotor but the power out is very limited, you can probably add 1 more coil or another driving coil in series to lower amp draw then add another 3 collection coils but I haven't tested anything out yet. ( my 2 cents :) )

As for trying to replicate romero's muller device, it is just a little bit too complicated for me right now, I will however continue experimenting with different size rotors ect... and when I have enough cash, I will attempt a smaller version of the muller device.

I can see it now, all those spikes spatter all over the sine wave,
I can't wait hehe :)
Regards Hitman

Hey check this out !
http://youtu.be/glRuwV9IlaY

[Hitman]

Hello all,
Waiting for parts is a bitch !! so I decided to do a little experiment as follows:
3 coil pairs, 1 pair rotor drivers and 2 pairs gen coils.
Rotor = 8 neo magnets.
1 - 6.18 VDC batter (almost dead).

When I started it up voltage went down to 6.13vdc and only drawing 53ma after a bit of tuning, now after running it for 2 hours, the voltage still hasen't dropped its still at 6.13.

I'm gonna let it run over night and see what happens.
Heres a pic of the unit and a scope shot of 1 of the coil pairs.

Cheers Hitman

[Romero]

Hello all,
Waiting for parts is a bitch !! so I decided to do a little experiment as follows:
3 coil pairs, 1 pair rotor drivers and 2 pairs gen coils.
Rotor = 8 neo magnets.
1 - 6.18 VDC batter (almost dead).

When I started it up voltage went down to 6.13vdc and only drawing 53ma after a bit of tuning, now after running it for 2 hours, the voltage still hasen't dropped its still at 6.13.

I'm gonna let it run over night and see what happens.
Heres a pic of the unit and a scope shot of 1 of the coil pairs.

Cheers Hitman

Hi,
Is that battery a 12 volt batt? if it is, don't let it stay too much at that low voltage, you might lose that battery very soon.
Romero

[Hitman]

Bahhh, when I woke up this morning the battery was down to 6.10 volts :(
I think there could be an improvement in coil placement.

@ romero
It was a 6 volt battery, I would never let a 12 volt battery get down to 6 volts !!! I'm a long time follower of all Mr Bedini's work :)

PS: I'll try to place my gen coils more like the adams motor and see if there is any improvement, I am also open to anyones suggestions from anyone !

Cheers Hitman

[Hitman]

Good evening all or should I say good morning,
Today I made a new rotor with only 4 magnets NSNS and used the same 1 pair of coils to drive the gen as in the adams motor. I then placed 1 gen coil at 30? from the 1st drive coil and placed another gen coil at 210? from the 1st drive coil or 30? from the 2nd drive coil.
After tuning the 1st gen coil for best placement I noticed the 2nd gen coil had much higher voltage peaks then the 1st gen coil. I removed the 1st gen coil and placed it at -30? from the 2nd drive coil and with ease was able to match the 2nd gen coils higher voltage ??????

Now when I hooked up everything to a FWBR's and a CAP I also took the BEMF of the drive coils and connected it to the same CAP. As soon as I connected a load (16volt incandescent lamp) my amp draw dropped from 102ma to 44ma and rpm's doubled but the little lamp was not very bright.
Voltage accross the CAP loaded was only 1.8VDC but I still got the effect I'm looking for :)
Ah yes before I forget voltage accross my CAP unloaded was a nice 74VDC.

I will make a video of this tomorrow and try to figure out why the coils beside the 1st drive coil don't have as much voltage as the ones on the 2nd drive coil.

Its late good night all,
Hitman

[Hitman]

heres the effect using 4 different input voltages:

http://youtu.be/Vjrv0PCk8u8

This evening I will be adding 2 more coils to the setup.

Cheers Hitman